Özet
In this thesis, it was aimed to determine the separation efficiencies of gravity concentration equipment and to reveal the concentration behavior of particles by investigating the separation mechanisms of coarse and fine sizes.
With this purpose, shaking tables, spiral concentrators, Falcon concentrator and MGS (Multi-gravity separator) were tested by using artificial feed, consisted of magnetite and quartz mixture. Sampling data, obtained from a chromite concentration plant using spiral concentrators, was also used in the results.
In the experimental studies, samples taken from feed, concentrate and tailings were sieved, grades of the size fractions were analyzed and recoveries, separation efficiencies, grades and grade ratios were evaluated on size basis.
As a result of the studies, it was observed that, in every condition, the separation efficiencies, due to particle sizes, increased as the particle size increased up to a certain point. After the maximum separation efficiency was obtained, the separation efficiency decreased as the particle size increased. In the evaluation of the average size-by-size separation efficiencies, maximum values were obtained as 95% in shaking tables, 78% in spiral concentrators and 48% in Falcon concentrator. Low concentration results was obtained in MGS tests with -150+38 μm feed material. Relations between the particle sizes and the separation efficiencies can be explained by quadratic polynomials.
In the region where the separation efficiencies increased due to the particle sizes, linear relations were observed between the settling rates of the particles and their separation efficiencies. Decreases in the separation efficiencies of the coarse particles, though, could be explained by Bagnold forces, which are directly proportional to the specific gravities of the particles and increase with the square of the particles’ diameter.
Künye
[1] R. O. Burt, Gravity Concentration Technology. London: Elsevier, 1984.
[2] A. L. Mular, D. N. Halbe, D. J. Barratt, Mineral processing plant design, practice and control proceedings. Colorado: Society for Mining, Metallurgy, and Exploration, Inc., 2002.
[3] C. Marion et al., “A design of experiments investigation into fine low-density ore processing using a 3-in. Knelson Concentrator,” in Physical Separation’17, 1–14, 2017.
[4] A. K. Majumder, “Modeling of particle fluid interactions in a flowing film concentrator,” Int. J. Miner. Process., Vol. 97, 7–19, 2010.
[5] W. H. Graf, Hydraulics of Sediment Transport, 3. Colorado: Water Resources Publications, LLc, 1998.
[6] B. A. Wills, T. J. Napier-Munn, Mineral Processing Technology: An Introduction to the Practical Aspects of Ore Treatment and Mineral Recovery, 7th ed., No. October. Elsevier Science & Technology Books, 2006.
[7] R. P. King, Modeling and simulation of mineral processing systems. Oxford: Butterworth-Heinemann, 2001.
[8] A. F. Taggart, Handbook of Mineral Dressing. New York: Wiley Interscience, 1945.
[9] G. G. Stokes, Mathematical and Physical Papers - III. Cambridge: Cambridge University Press, 1905.
[10] R. J. Cheel, “Unidirectional fluid flow and sediment transport,” Introduction to Clastic Sedimentology, Ontario: Brock University, 55–73, 2005.
[11] O. C. Ralston, “Principles of Mineral Dressing by A. M. Gaudin,” J. Phys. Chem., Vol. 44, No. 4, 532–533, 1940.
[12] R. G. Richards, M. K. Palmer, “High capacity gravity separators a review of current status,” Miner. Eng., Vol. 10, No. 9, 973–982, 1997.
[13] R. A. Bagnold, “Experiments on a Gravity-Free Dispersion of Large Solid Spheres in a Newtonian Fluid under Shear,” Proc. R. Soc. A Math. Phys. Eng. Sci., Vol. 225, No. 1160, 49–63, 1954.
[14] G. Ferrara, U. Preti, P. Bevilacqua, “Modelling the basic separation phenomena in flowing film concentration processes,” in International Mineral Processing Congress, 379–386, 1993.
[15] Open University Course Team, “Principles and processes of sediment transport,” Waves, Tides and Shallow-Water Processes, 2nd ed., Elsevier, 96–124, 1999.
[16] P. N. Holtham, “Particle transport in gravity concentrators and the Bagnold effect,” Miner. Eng., Vol. 5, No. 2, 205–221, 1992.
[17] J. R. D. Francis, “Experiments on the motion of solitary grains along the bed of a water stream,” Prec. R. Sac. Lend., Vol. 332, No. A, 443–471, 1973.
[18] J. E. Abbott, J. R. D. Francis, “Saltation and suspension trajectories of solid grains in a water stream,” Phil. Trans. R. Soc. Lend., Vol. 284, No. A, 225–254, 1977.
[19] B. M. Sumer, B. Oguz, “Particle motions near the bottom in turbulent flow in an open channel, Part 1,” J. Fluid Mech., Vol. 86, 109–127, 1978.
[20] B. M. Sumer, R. Deirgaard, “Particle motions near the bottom in turbulent flow in an open channel, Part 2,” J. Fluid Mech., Vol. 109, 311–337, 1981.
[21] M. R. Leeder, “‘Bedload’ dynamics: grain-grain interactions in water flows,” Earth Surf. Process., Vol. 4, 229–240, 1979.
[22] G. Hetsroni, “Particles-turbulence interaction,” Int. J. Multiph. Flow, Vol. 15, 735–746, 1989.
[23] R. A. Bagnold, “An approach to the sediment transport problem from general physics,” U.S Geol. Surv. Prof. Pap. 422-I, I1–I37, 1966.
[24] H. Nasr-el-Din, C. A. Shook, J. Colwell, “The lateral variation of solids concentration in horizontal slurry pipeline flow,” Int. J. Multiph. Flow, Vol. 13, No. 5, 661–670, 1987.
[25] S. Abdinegoro, A. C. Partridge, “Flow characteristics of a pinched sluice,” in Proc. Aus. IMM Conference, 79–88, 1979.
[26] G. K. N. S. Subasinghe, E. G. Kelly, “Modelling pinched sluice type concentrators,” in Control ’84 Conference, 87–95, 1984.
[27] M. S. Yalin, Mechanics of Sediment Transport. Oxford: Pergamon, 1972.
[28] R. O. Burt, “Role of gravity concentration in modern processing plants,” Miner. Eng., Vol. 12, No. 11, 1291–1300, 1999.
[29] A. Wells, “Some experiences in the design and optimisation of fine gravity concentration circuits,” Miner. Eng., Vol. 4, No. 3–4, 383–398, 1991.
[30] E. Forssberg, T. Nordquist, “Pilot plant trials of new gravity concentration equipment,” Miner. Met. Proc., 87–89, 1987.
[31] A. R. Laplante, “Centrifuge units for gravity separation - an update,” in 32nd Annual Meeting of the Canadian Mineral Processors, 475–488, 2000.
[32] R. O. Burt, G. Korinek, S. R. Young, C. Deveau, “Ultrafine tantalum recovery strategies,” Miner. Eng., Vol. 8, No. 8, 859–870, 1995.
[33] S. Hearn, “The use of hindered settlers to improve iron ore gravity concentration circuits,” 2000.
[34] R. J. Manser, R. W. Barley, B. A. Wills, “The shaking table concentrator - The influence of operating conditions and table parameters on mineral separation - The development of a mathematical model for normal operating conditions,” Miner. Eng., Vol. 4, No. 3–4, 369–381, 1991.
[35] R. I. Mackie, P. Tucker, “Simulation and optimisation of gravity concentration circuits,” in Proceedings of International Symposium on the Mathematical Modelling of Materials’ Processing Operations, 148–160, 1987.
[36] K. J. Pillai, “Mathematical models of gravity separation devices and their use in optimisation and control,” in Proceedings of the International Symposium on Extractive Metallurgy and Materials Science, 1263–1279, 1987.
[37] E. G. Kelly, D. J. Spottiswood, Introduction to Mineral Processing. New York: Wiley Interscience, 1982.
[38] K. F. Tromp, “New methods of computing the washabilities of coals,” Colliery Guard., Vol. 154, 955–959, 1009, 1937.
[39] B. S. Gottfried, P. S. Jacobsen, “Generalized distribution curve for characterizing the performance of coal-cleaning equipment,” in U.S. Bureau of Mines Report of Investigations, 1977.
[40] A. P. Prosser, “Analysis of mineral separation processes,” Chem. Proc. Eng., 88–86, 96, 1969.
[41] R. D. Pascoe, M. R. Power, B. Simpson, “QEMSCAN analysis as a tool for improved understanding of gravity separator performance,” Miner. Eng., Vol. 20, No. 5, 487–495, 2007.
[42] C. Philander, A. Rozendaal, “A process mineralogy approach to geometallurgical model refinement for the Namakwa Sands heavy minerals operations, west coast of South Africa,” Miner. Eng., Vol. 65, 9–16, 2014.
[43] J. D. Grobler, J. B. Bosman, “Gravity separator performance evaluation using Qemscan® particle mineral analysis,” in The 7th International Heavy Minerals Conference ‘What next,’ 91–98, 2009.
[44] C. Bergmann, V. Govender, A. A. Corfield, “Using mineralogical characterisation and process modelling to simulate the gravity recovery of ferrochrome fines,” Miner. Eng., Vol. 91, 2–15, 2016.
[45] E. G. Kelly, G. K. N. S. Subasinghe, “Gravity performance curves: A re-examination,” Miner. Eng., Vol. 4, No. 12, 1207–1218, 1991.
[46] N. Aslan, “Modeling and optimization of Multi-Gravity Separator to produce celestite concentrate,” Powder Technol., Vol. 174, No. 3, 127–133, 2007.
[47] N. Aslan, Y. Cebeci, “Application of Box–Behnken design and response surface methodology for modeling of some Turkish coals,” Fuel, Vol. 86, No. 1–2, 90–97, 2007.
[48] A. L. Martinez, A. S. Uribe, F. R. P. Carrillo, J. A. Coreno, J. C. Ortiz, “Study of celestite flotation efficiency using sodium dodecyl sulfonate collector: factorial experiment and statistical analysis of data,” Int. J. Miner. Process., 83–97, 2003.
[49] N. Aslan, “Multi-objective optimization of some process parameters of a multi-gravity separator for chromite concentration,” Sep. Purif. Technol., Vol. 64, No. 2, 237–241, 2008.
[50] R. H. Goodman, C. A. Brown, I. C. Ritchie, “Advanced gravity concentrators for improving metallurgical performance,” in Minerals and Metallurgical Processing, 79–86, 1985.
[51] A. B. Holland-Batt, “The dynamics of sluice and spiral separations,” Miner. Eng., Vol. 8, No. 1–2, 3–21, 1995.
[52] Y. Atasoy, D. J. Spottiswood, “A study of particle separation in a spiral concentrator,” Miner. Eng., Vol. 8, No. 10, 1197–1208, 1995.
[53] A. B. Holland-Batt, “Spiral separation: theory and simulation,” Miner. Process. Extr. Metall., Vol. 98, No. C, 46–60, 1989.
[54] R. G. Richards, D. M. MacHunter, P. J. Gates, M. K. Palmer, “Gravity separation of ultra-fine (-0.1 mm) minerals using spiral separators,” Miner. Eng., Vol. 13, No. 1, 65–77, 2000.
[55] C. Bazin et al., “Size recovery curves of minerals in industrial spirals for processing iron oxide ores,” Miner. Eng., Vol. 65, 115–123, 2014.
[56] E. J. Pryor, Mineral Processing, 3rd ed. London: Applied Science Publishers, 1965.
[57] P. Tucker, “An approach to modelling industrial unit processes: Application to a spiral concentrator for minerals,” Appl. Math. Model., Vol. 9, No. 5, 375–379, 1985.
[58] S. K. Das, K. M. Godiwalla, L. Panda, K. K. Bhattacharya, R. Signh, S. P. Mehrotra, “Mathematical modeling of separation characteristics of a coal-washing spiral,” Int. J. Miner. Process., Vol. 84, 118–132, 2007.
[59] R. Sivamohan, E. Forssberg, “Principles of spiral concentration,” Int. J. Miner. Process., Vol. 15, 173–181, 1985.
[60] A. B. Holland-Batt, P. N. Holtham, “Particle and fluid motion on spiral separators,” Miner. Eng., Vol. 4, 457–482, 1991.
[61] A. Steinmüller, “Development and application of simple process models for spiral concentrators,” Heavy Miner., 167–172, 2005.
[62] A. B. Holland-Batt, “Interpretation of spiral and sluice tests,” Trans. Instn. Min. Met., No. C, 99, 1990.
[63] R. Dallaire, A. Laplante, J. Elbrond, “Humphrey’s spiral tolerance to feed variations,” CIM Bull., 128–134, 1978.
[64] A. R. Laplante, J. A. Finch, “The origin of unusual cyclone performance curves,” Int. J. Miner. Process., Vol. 13, 1–13, 1984.
[65] B. S. Savage, D. J. Jeffrey, “The stress tensor in a granular flow at high shear rates,” J. Fluid Mech., Vol. 110, 255–272, 1981.
[66] D. M. Hanes, D. L. Inman, “Observations of rapidly flowing granular-fluid materials,” J. Fluid Mech., Vol. 150, 357–380, 1985.
[67] A. Gupta, D. S. Yan, Mineral Processing Design and Operations: An Introduction. Oxford: Elsevier, 2006.
[68] R. S. Fitzpatrick, Y. Ghorbani, P. Hegarty, G. Rollinson, “Quantitative mineralogy for improved modelling of shaking tables,” in International Mineral Processing Congress, 1–19, 2016.
[69] W. Wang, H. Shu, C. Jin, “A mathematical model of the shaking table and its application,” in International Mineral Processing Congress, 387–393, 1993.
[70] R. J. Manser, R. W. Barley, B. A. Wills, “Development of a mathematical model of a shaking table concentrator,” in Proceedings of 19th APCOM Symposium, 631–636, 1986.
[71] Z. Luo, “A study of the motion characteristics and their effect on the separation of shaking table,” in Proceedings of 2nd Meeting of Gravity and Magnetic Separation, 631–637, 1986.
[72] R. Razali, T. J. Veasey, “Statistical modelling of a shaking table separator part one,” Miner. Eng., Vol. 3, No. 3–4, 287–294, 1990.
[73] P. Tucker, K. A. Lewis, P. Wood, “Computer optimisation of a shaking table,” Miner. Eng., Vol. 4, No. 3–4, 355–367, 1991.
[74] B. V. Rao, “Weibull partition surface representation for gravity concentrators,” Miner. Eng., Vol. 17, No. 7–8, 953–956, 2004.
[75] R. S. Fitzpatrick, Y. Ghorbani, P. Hegarty, G. Rollinson, T. Mildren, K. Fergusson, “Recovery of fine tungsten-bearing minerals from waste streams using modified Multi-Gravity Separator,” in MEI Physical Separation ’17, 1–18, 2017.
[76] A. Traore, P. Conil, R. Houot, M. Save, “An evaluation of the Mozley MGS for fine particle gravity separation,” Miner. Eng., Vol. 8, No. 7, 767–778, 1995.
[77] B. Knelson, “The Knelson Concentrator: metamorphosis from crude beginning to sophisticated world wide acceptance,” Miner. Eng., Vol. 5, 1091–1097, 1992.
[78] B. Knelson, R. Jones, “A new generation of Knelson Concentrators: a totally secure system goes on line,” Miner. Eng., Vol. 7, 201–207, 1994.
[79] A. R. Laplante, L. Huang, M. Noaparast, N. Nickoletopoulos, “A philosopher’s stone: turning tungsten and lead into gold-The use of synthetic ores to study gold gravity separation,” in Proceedings of 27th Annual Meeting of Canadian Mineral Processors, 379–394, 1995.
[80] A. R. Laplante, F. Woodcock, M. Noaparast, “Predicting gravity separation gold recovery,” Miner. Met. Process., 74–79, 1995.
[81] A. R. Laplante, N. Nickoletopoulos, “Validation of a Falcon model with a synthetic ore,” Can. Met. Quart., Vol. 37, No. 1, 7–13, 1997.
[82] V. Gunaraj, N. Murugan, “Application of response surface methodology for predicting weld bead quality in submerged arc welding of pipes,” J. Mater. Process. Technol., Vol. 88, No. 1–3, 266–275, 1999.
[83] O. Kokkilic, R. Langlois, K. E. Waters, “A design of experiments investigation into dry separation using a Knelson Concentrator,” Miner. Eng., Vol. 72, 73–86, 2015.
[84] J. S. Kwak, “Application of Taguchi and Response Surface Methodologies for geometric error in surface grinding process,” Int. J. Mach. Tools Manuf., Vol. 45, 327–334, 2005.
[85] D. C. Montgomery, Design and Analysis of Experiments, 8th ed. John Wiley & Sons, 2012.
[86] M. Zhou, O. Kokkilic, R. Langlois, K. E. Waters, “Size-by-size analysis of dry gravity separation using a 3-in. Knelson Concentrator,” Miner. Eng., Vol. 91, 42–54, 2016.
[87] M. Greenwood, R. Langlois, K. E. Waters, “The potential for dry processing using a Knelson Concentrator,” Miner. Eng., Vol. 45, 44–46, 2013.
[88] P. H. Ancia, J. Frenay, P. H. Dandois, “Comparison of the Knelson and Falcon centrifugal separators,” in Innovation in physical separation technologies: Richard Mozley Symposium, 53–62, 1997.
[89] T. McKeon, G. H. Luttrell, “Optimization of multistage circuits for gravity concentration of heavy mineral sands,” Miner. Metall. Process., Vol. 29, No. 1, 1–5, 2012.
[90] T. P. Meloy, “Analysis and optimization of mineral processing and coal-cleaning circuits - Circuit analysis,” Int. J. Miner. Process., Vol. 10, No. 1, 61–80, 1983.
[91] G. H. Luttrell, J. N. Kohmuench, F. L. Stanley, G. D. Trump, “Improving spiral performance using circuit analysis,” Miner. Metall. Process., Vol. 5, No. 4, 16–21, 1998.
[92] T. McKeon, G. H. Luttrell, “Application of linear circuit analysis in gravity separator circuit design,” in Heavy Minerals, 179–184, 2005.
[93] N. F. Shulz, “Separation Efficiency,” Trans. AIME, Vol. 247, 81–87, 1970.
[94] A. B. Holland-Batt, “Efficiency in Batch Separations,” in Trans. Instn. Min. Metall, C12-23, 1971.
[95] K. S. E. Forssberg, E. Sandström, “Operational Characteristics of Reichert Cone in Ore Processing,” in 13. International Mineral Processing Congress, 1421–1452, 1981.
[96] S. L. Ergun, “Daralan oluklarda akış koşulları ve geometrik özelliklerin ayırma etkisinin incelenmesi,” Hacettepe University, 1995.
[97] K. Smith, M. Vinchoff, Operations and Maintanance Manuel of Falcon Semi-Batch Concentrator Laboratory Model L40. 14, 2007.
[98] C. T. Yang, “Noncohesive Sediment Transport,” Erosion and Sedimentation Manual, United States Department of the Interior, Bureau of Reclamation, Technical Service Center, Sedimentation and River Hydraulics Group, 1–111, 2006.
[99] A. R. Laplante, M. Buonvino, A. Veltmeyer, J. Robitaille, G. Naud, “Case studies with the Falcon concentrator,” in 25th Annual Meeting of the Canadian Mineral Processors, 1–22, 1993.
[100] C. Deveau, “The evolution of Falcon Continuous Concentrators at Tantalum Mining Corporation of Canada,” in 32nd Annual Meeting of the Canadian Mineral Processors, 1–17, 2000.
[101] S. Koppalkar, A. R. Laplante, “Effect of operating variables in Knelson Concentrators : a pilot-scale study,” in 39th Annual Meeting of the Canadian Mineral Processors, 247–258, 2007.
[102] A. R. Laplante, “Marvel Loch arazi raporu,” 2003.
[103] A. B. Holland-Batt, “The effect of feed rate on the performance of coal spiral,” in Coal Preparation, 199–222, 1994.
[104] D. B. Hyma, J. A. Meech, “Preliminary tests to improve the iron recovery from the -212 micron fraction of new spiral feed at quebec cartier mining company,” Miner. Eng., Vol. 2, No. 4, 481–488, 1989.
[105] Y. Hassanzadeh, “Hydraulics of sediment transport,” Hydrodynamics - Theory and Model, J.-H. Zheng, Ed. InTech, 23–58, 2012.
[106] P. N. Holtham, “Particle transport in gravity concentrators and the Bagnold effect,” Miner. Eng., Vol. 5, No. 2, 205–221, 1992.
[107] B. W. Matthews, P. N. Holtham, K. Golab, “Computational and experimental investigation of spiral concentrator flows,” in COAL98 Conference, 415–421, 1998.
[108] R. C. Richards, D. M. MacHunter, P. J. Gates, M. K. Palmer, “Gravity separation of ultra-fine (-0.1 mm) mineral using spiral separators,” Miner. Eng., Vol. 13, 65–77, 2000.
[109] D. J. Miller, “Design and operating experience with the Goldsworthy mining limited Batac jig and spiral separator iron ore beneficiation plant,” Miner. Eng., Vol. 4, 411–435, 1991.
[110] D. Gucbilmez, S. L. Ergun, “Spiral zengi̇nleşti̇ri̇ci̇lerde tane boyunun performansa etki̇si̇ni̇n incelenmesi̇,” Hacettepe University, 2013.
[111] D. B. Hyma, J. A. Meech, “Preliminary tests to improve the iron recovery from the -212 micron fraction of new spiral feed at Quebec Cartier Mining company,” Miner. Eng., Vol. 2, 481–488, 1989.
[112] A. Shields, W. P. Ott, J. C. van Uchelen, “Application of similarity principles and turbulence research to bedload movement,” Pasadena, California, 1936.
[113] F. Hjulstrom, “The morphological activity of rivers as illustrated by River Fyris,” Bullettin Geol. Inst., Vol. 25, 442–452, 1935.
[114] Y. C. Agrawal, H. C. Pottsmith, “Instruments for particle size and settling velocity observations in sediment transport,” Mar. Geol., Vol. 168, No. 1–4, 89–114, 2000.
[115] H. A. Einstein, “The bed-load function for sediment transportation in open channel flows,” Soil Conservation Service. United States Department of Agriculture, Soil Conservation Service, 1–71, 1950.
[116] F. Engelund, E. Hansen, “A monograph on sediment transport in alluvial streams,” in Teknisk Forlag, 31–59, 1972.
[117] P. Ackers, W. R. White, “Sediment transport: New approach and analysis,” J. Hydraul. Div., Vol. 99, No. HY11, 2041–2060, 1973.
[118] J. R. L. Allen, Principles of Physical Sedimentology. London: Allen & Unwin, 1985.
